Lixin fittings teach your vehicle conservation tips :

    The car can not be left

    After the engine is started , particularly in winter , to be allowed to idle for a period of time prior to the turbocharger rotor at high speed to allow sufficient oil lubricated bearings . So, do not start just after Meng throttle to prevent damage to the turbocharger oil seal.

    Can not turn off immediately

    After the high-speed operation of the engine for a long time , should be idling 3-5 minutes and then turn off. When the engine work , some of the oil supply turbocharger rotor bearing lubrication and for cooling . After running the engine suddenly stopped , the oil pressure to drop rapidly to zero , the high temperature reached turbocharger middle part of the heat bearing housing can not be taken away quickly , and high-speed rotation inertia turbocharger rotor while still Therefore, if the engine is hot state a sudden stop , causing retention turbocharger oil overheating and damage to the bearing and shaft. Particularly to prevent sudden flameout Meng kicks after the throttle .

    Keep clean

    Time to clean the air filter to prevent dust and other impurities from entering the high-speed rotation of the compressor impeller speed instability caused or exacerbated wear bushings and seals. Engine oil and filter must be kept clean to prevent debris from entering , otherwise oil lubrication capacity decreased , resulting in premature turbocharger scrapped .

    When removing the supercharger, to keep clean, all fittings must use a clean cloth to plug well, to prevent debris from falling into the turbocharger rotor damage . Due to high temperatures often in the turbocharger operation , its oil pipeline due to high temperature, internal oil prone parts of coke , this will result in insufficient lubrication of the bearing turbocharger damage . Thus , oil pipeline after running for some time to be cleaned .

    According to Fong fittings understand , the car for a long time will inevitably be some unexpected glitches , no one can predict how things will happen the next second , but we still have to know more, to know more about , so that we encounter these problem , good to deal with .

1 valve spring break

After the valve spring break, spring break can be removed to turn off the two installed, you can use. May also find a 1 mm thick metal, cut into 1 mm than the diameter of the spring disc , cut a hole inside diameter smaller than the spring diameter 4 mm , 6 mm outer edge every 4 mm length of cut rip , cut after every one folded a form -sided spring slot , and then turn around a spring loaded metal tank can be used.

2 or diaphragm pump diaphragm rupture or break

Remove the diaphragm pump can be disassembled , with plastic wood, electrical insulation bakelite or plastic sheeting to the original shape, size, saw filing shaping and polishing installed.

3 holes slider

Screw slider will result in spills or rod loose, it does not work . Repairs can be original screw with a hammer pounding flat , so both sides of the expansion increases again tightened well, but not many times demolished, this time until the next maintenance time .

4 broken fan belt

The belt can be tied or broken open using open approach to stop the car drove away .

5 inlet and outlet hose rupture

Rupture is not available coated with a layer of soap wrapped cloth leaks ; such as rupture is large , you can cut the hose rupture , put in the middle of a bamboo or iron pipe and tied tight .

6 . Tubing joints leak

When using a motor vehicle , such as engine oil pipe joints leak, mostly flared tubing and tubing nut is not sealed due. Available yarn wound on the edge of the next speaker , then the tubing and tubing fittings and tighten the nut ; can also be chewed bubble gum or maltose into a paste , applied to the seat tubing nut mouth , let it dry condensate newcomer seal.

7 head appeared trachoma and oil spills, leaks

According to trachoma size , choose the appropriate specifications for electrical fuses , hand hammer gently drop into the blisters, you can eliminate oil spills, leaks .

8 pipeline break

Can find a compatible with tubing diameter rubber or plastic tubing pipe sockets when broken. If the socket is not tight enough , then the ends tied tight to prevent leakage.

9 pipeline rupture

Can be ruptured pipeline rupture when rubbed clean, apply soap , with a cloth or tape wrapped around the pipe rupture and tied tight , and then coated with a layer of soap.

10. The tank damage

It is understood Lixin fittings , motor vehicle in use, found that leak from the tank , oil spills can be wiped clean place, with soap or bubble gum coated in oil at the temporary blockage ; with epoxy adhesive patch , the better.